CT18R – Kylcentrifuger
Ring 042-300 91 30 eller maila info@labteamet.com
When “eco setting” is enable, if the door is not opened or closed and no operations are performed for 10 minutes, the cooling device is automatically stopped.
Max. 25% stand-by electricity is reduced, comparing the stand-by electricity without eco setting. (under in-house evaluation) When a user forgets to turn off the main power switch for a long time (such as overnight), stand -by electricity consumption isreduced.
Set “eco” function and contribute energy saving.
Easy-to-Read Capacitive Touch Panel accepts latex gloves operations.
Timer starts counting after the set speed is attained. So acceleration time is excluded from the centrifugation time.You can obtaion higher reproducible centrifugation result with this function.
It easier to obtain more consistent separation results because there is less variation in acceleration times due to different rotors and sample volumes.
Total run hours * can be displayed on the operation panel. It is useful as a guideline of the periodical maintenance. * Including acceleration time regardless a setting of the Actual Run Timer
Remote monitoring application “himac View” is available for CT18R, CR30NX and CP-NX series.
”himac View” monitors, operates of start or stops a centrifuge with iPhone ™ or Android ™ Phone via Wi-Fi ®.
“himac View” monitors up tp 16 units of CT18R, CR30NX or CP-NX series in the LAN access network.
* Optional LAN board in CT18R is required to use “himac View”. For more details contact the nearest sales representative.
Just place a rotor on the drive shaft.
The rotor is automatically locked by centrifugal force once it starts spinning.
When the rotor comes to complete stop, the lock is automatically released.
| Model | CT18R | |
|---|---|---|
| Max. Speed (rpm) | 18,000 (T18A41 rotor) | |
| Max.RCF (xg) | 31,100 (T18A41 rotor) | |
| Maximum Capacity | 1,000mL (250ml x 4 : T5SS31 rotor) | |
| Speed Setting Range (rpm) | 300 – 18,000 | |
| Timer | 1 to 99 min. (in increments of 1 min.) with HOLD function or 1 to 59 sec. with HOLD function |
|
| Temperature Setting Range (ºC) | -20 to +40 | |
| Acceleration/Deceleration Mode | Accel: 10 modes, Decel: 10 modes and brake-free | |
| Memory-based programmed operation | 99 programs, including 3 direct select buttons | |
| Drive Unit | Induction motor (Inverter) | |
| Refrigerator | 300W Hermetic compressor (Refrigerant: HFC 134a) | |
| Rotor stop signal | Select from 5 melodies, beep and mute | |
| Interface connection | LAN X 1 (Option) | |
| Safety functions | Door interlock, dual overspeed detector, Rotor ID detector, imbalance detector, over-temperature detector |
|
| Noise level | Less than 55dB by fixed angle rotor Less than 59dB by swinging bucket rotor |
|
| Compliance with standard | CE, cCSAus * | |
| Heat radiation | 650W | |
| Power Requirement | (115V -127V model) | ±10% 60Hz 15A (ordering number: 915617C3) |
| (200 – 240V model) | ±10% 50Hz 8A (ordering number: 915617C1 and 915617C2 **) | |
| Dimentions (mm) | 634 mm (W) X 550 mm (D) X 340 mm (H) (Height to the table: 291 mm) |
|
| Weight (kg) | 80 | |
| Installation Environment | Ambient temperature for operation:2℃ to 40 ℃ Ambient temberature for assuring performance: 15℃ to 25℃ |
|
| Model | Part No. | Rotor ID | Max. Speed (rpm) |
Max. RCF (xg) |
Nominal Capacity (pcs x ml) |
|
|---|---|---|---|---|---|---|
 |
T18A41 | 91570000 | 30 | 18,000 | Out: 31,100 In: 26,400 |
36 x 2/1.5 |
| 18,000 | Out: 27,100 In: 22,400 |
36 x 0.7 | ||||
| 15,100 | Out: 19,900 In: 16,600 |
36 x 1/0.5 | ||||
| 15,100 | Out: 20,800 In: 17,500 |
36 x 0.5 | ||||
| 18,000 | Out: 28,500 In: 23,800 |
36 x 0.5 | ||||
| 18,000 | Out: 30,100 In: 25,400 |
36 x 0.4/0.25 | ||||
| 18,000 | 23,200 | 18 x 0.2 | ||||
 |
T15A39 | 91589900 | 49 | 15,000 | 21,500 | 24 x 2/1.5 |
| 15,000 | 21,500 | 24 x 0.7 | ||||
| 15,000 | 21,500 | 24 x 1/0.5 | ||||
| 15,000 | 21,500 | 24 x 0.5 | ||||
| 15,000 | 21,500 | 24 x 0.5/0.4 | ||||
| 15,000 | 21,500 | 24 x 0.4/0.25 | ||||
 |
T15A46 | 91583600 | 39 | 15,000 | 22,000 | 12 x 5 * |
| Rotor cover is slod separately. | ||||||
 |
T15A41 | 91591300 | 42 | 15,000 | 22,260 | 4 x 50 (TC) or 4 X 15 (TC) |
| 15,000 | 14,200 | 4 x 5 * | ||||
| 11,000 | 11,970 | 4 x 50 (TC) or 4 X 15 (TC) |
||||
 |
T12A41 | 91570100 | 20 | 12,000 | 18,000 | 6 x 50 (TC) |
| 10,000 | 12,200 | 6 x 15 (TC) | ||||
 |
T9A31 | 91587400 | 24 | 9,000 | 10,600 | 8 x 50 (TC) |
| 9,000 | 10,300 | 8 x 15 (TC) | ||||
| 9,000 | 9,700 | 8 x 13 | ||||
 |
T12A42 | 91570200 | 21 | 12,000 | 17,100 | 6 x 80 6 x 70 |
LEASING / HYRA / AVBETALNING
Vårt samarbete med Svea gör att du snabbt och enkelt får förslag på finansiering som passar dina behov Finansiering upp till 100%. Ni slipper binda ert kapital. Läs mer om leasing och allriskförsäkring.
Investera nu i rätt utrustning, för att säkra er konkurrenskraft, kapacitet och tillgång till vital utrustning Sprid kostnaden över den tid som utrustningen används. Utrustningen som säkerhet för finansieringen.
LEASING / HYRA / AVBETALNING
Vårt samarbete med Svea gör att du snabbt och enkelt får förslag på finansiering som passar dina behov Finansiering upp till 100%. Ni slipper binda ert kapital. Läs mer om leasing och allriskförsäkring.
ANMÄL DIG TILL VÅRT NYHETSBREV
Din epost (obligatorisk)
Har du lagt till produkter till ”Mina produkter” så glöm inte skicka iväg din pris- eller produktförfrågan också. Skapa gärna ett konto så sparas alla dina förfrågningarna under ”Mitt konto” sidan.
